[Manager]
UseIOLabCard=0

GrabCtlRegKey=HKEY_LOCAL_MACHINE\SOFTWARE\AVT\Site Config\GrabCtl
GrabDefaultCtlName=Grabber1
OHCtlRegKey=HKEY_LOCAL_MACHINE\SOFTWARE\AVT\Site Config Demo\OHCtl
OHDefaultCtlName=OH
YBoardCtlRegKey=HKEY_LOCAL_MACHINE\SOFTWARE\AVT\Site Config\YBoardCtl
YBoardDefaultCtlName=Station1

; GrabberMode:	0 - real	1- Demo		2 - Test
GrabberType=0

; Head type: 0 - Area, 1 - Coldseal, 2 - LCCD
FrontHeadType=2
BackHeadType=0
TrafficTowerLightChangeTimeOut=4000

OpenPressControl=1
InverseMovingY=1
[Devices]
; The Buzzer mode in the alarm: 0 - OFF 1- ON 2- Slow 3- Fast
BuzzerMode=0
; Label Inserter Relay ID
RelayID=5
; Label Inserter Pulse Width
PulseWidth=100
;Label inserter signal type 0 - level 1- pulse
SignalType=1

[Head0]
ApplyInterpulationInThreeLine=1
FirstLineUpDir=0
; 0 - Red, 1 - Blue, 2 - Green;
FirstChannel=1
LastChannel=0
ExposureCalibMethod=0
OpticSensorActive=0
MaxGainPrecentageAllowed=150
ApplyGainCalib=1
ReverseMultiCamShiftY=0
SeparateMultiCamImage=0
MaxAllowedWedMovingDistanceMM=10
NormalizeMeterCount=0
LabelSensorRepeatsTest=30
LabelSensorRepeatsTestPercent=30
TimeBetweenSensorMeasurments=500
NumberOfMeasurment=5
;ePosLedDisable = 0,
;ePosLedOnDemand = 1,
;ePosLedOnInterval = 2,
;ePosLedOnIntervalAndOnDemandAfterStop = 3,
ImagePositionByLedMode=0
;in onDemand-turn led on Pos + PositionLedIntervalMM after prev led found, in case onInterval turn led on each PositionLedIntervalMM
PositionLedIntervalMM=5000
PositionLedDelta=600
;relevant on ePosLedOnIntervalAndOnDemandAfterStop mode
TurnLedAfterStopOnPosMM=50
DbgOutMsgOn=0
;packs
EjectorSafeModeSP=0
DistFromOStoEjectorMM=100
;enable flag: disable=0; noize filter=1, blank lenght=2; both=3
OpticSensorFilterSF=0
NoizePicksSizeMM=25

[General]
MinPressSpeedReq=-10
GetSpeedLimitFromSystem=0
TimeThToDecideOnZeroSpeed=500
TimeThToDecideOnSpeedTooHigh=200
IgnoreInComingSpeedJumps=0
SpeedJumpsToIgnoreFactor=1.5
NumSpeedJumpsToIgnore=10
EndOfRollMinTimeInterval=5000
EndOfRollMinLength=0
DoGoodPackCountByHardware=0
DoPackCountByHardware=0
CheckPacksCounter=1
SWPcountAndHPcountRatioAllowed=0.6
CheckMaxRunLengthMeters=1
; close to signend long by encoder ticks num (0.04mm)
MaxRunLengthMeters=85000
ApplyDistanceToSpicerInHardWare=1

[General Thread]
GeneralThreadPollingTime=250
SpeedPollingTimeDilate=2
MetersPollingTimeDilate=1
RLMPollingTimeDilate=1
GetPositionPollingTimeDilate=10

[Any Speed]
AnySpeedEnable=1
LinesBetweenLedsAnySpeed=10
AddToMaxSpeedWhenAnySpeedPercent=5
OptimizeAnySpeedGrab=1
ResampleAnySpeedBufferInterval=30
NumThreadsExtractLines=1
NumThreadsGetNextLines=1
NumThreadsResampleLines=1
ProcessingTimeLimit=0
UseInitCommandGuard=0
CheckSpeedOutOfRangeAnySpeed=1

[Dual Head]
; Defines the dual head mode for the system
; 0 - WE0 - garab without counting (not the same material)
; 1 - WE1 - grab with RPG counting (the same material)
DualHeadMode=1
; Which head will flash first while the system is in serface run?
; 0 - First head (Front) will flash first on surface run
; 1 - Second head (back) will flash first on surface run
FirstToFlashOnSurfaceRun=0
; Inverse distance sign
ShouldInverseDistanceSign=0
XFrontReferencePointPosition = 0
YFrontReferencePointPosition = 0
XBackReferencePointPosition = 0
YBackReferencePointPosition = 600


[RLM]
; Allowed error in mm for each reading from hardware.
RLMAllowedReadingErrorTh=15
; correction factor
CorrectionFactor=1.0
;The size off the rlm defect.
RLMDefectSize=5
;The sigma size.
RLMSigma=2
; flexo system can be approximated by special formula.(in case of pressZero).
ApproximateResults=0

[Press Control]
MetersToWait=0


